Eaton PC917-2000 Guide de l'utilisateur Page 69
- Page / 116
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Switched ePDU Admin Using Serial or Telnet
Eaton
®
User's Guide for Basic, Monitored, and Switched ePDUt S 164202115 Rev 1
55
Table 13. SNMP Configuration
Setting Description
Public Community Name* Up to 20 characters long (default is “public”).
Private Community Name* Up to 20 characters long (default is “private”).
Trap Community Name (public)* Up to 20 characters long (default is “public”).
Public Community Password* Up to 20 characters long (default is “public”).
Private Community Password* Up to 20 characters long (default is “private”).
Trap IP Address Enter in standard dot notation (for example, 192.168.168.100).
All traps are sent to this address at port 161.
SNMP Enabled* Enabled or Disabled.
When running, the SNMP server is bound to port 162.
Trap User Login Enabled or Disabled.
When enabled, a trap is sent to the Trap IP Address each time a
user logs in to or logs out of the serial, Telnet, or Web interfaces.
Trap Failed Login Enabled or Disabled.
When enabled, a trap is sent to the Trap IP Address when a user
fails to log in three times in a row with an invalid username or
password to the serial, Telnet, or Web interfaces.
Trap Outlet Activity Enabled or Disabled.
When enabled, a trap is sent to the Trap IP Address each time an
outlet action occurs.
Trap System On/Off Enabled or Disabled.
When enabled, a trap is sent to the Trap IP Address each time the
ePDU completes booting up.
Trap Voltage/Current Threshold Enabled or Disabled.
When enabled, a trap is sent to the Trap IP Address each time the
measured voltage or current rises above the upper threshold or falls
below the lower threshold (as set in the “Voltage/Current Threshold
Setup” on page 49).
Trap Temperature Threshold Enabled or Disabled.
When enabled, a trap is sent to the Trap IP Address each time the
measured temperature for an enabled temperature sensor rises
above the upper threshold or falls below the lower threshold (as set
in the “Temperature Sensor Setup” on page 46).
Trap Humidity Threshold Enabled or Disabled.
When enabled, a trap is sent to the Trap IP Address each time the
measured humidity for an enabled humidity sensor rises above the
upper threshold or falls below the lower threshold (as set in the
“Humidity Sensor Setup” on page 47).
Trap Contact Threshold Enabled or Disabled.
When enabled, a trap is sent to the Trap IP Address each time an
enabled contact sensor changes state from Closed to Open or from
Open to Closed.
* Requires a soft reboot to take effect (select Soft Reboot from the Unit Configuration page, then click
Save Changes).
- Eaton User's Guide 1
- 164202115 1
- Special Symbols 4
- Table of Contents 5
- List of Figures 7
- Chapter 1 Introduction 9
- Features 10
- CONSERVER CES INSTRUCTIONS 11
- IMPORTANT SAFETY INSTRUCTIONS 11
- SAVE THESE INSTRUCTIONS 11
- AUFBEWAREN 12
- GUARDE ESTAS INSTRUCCIONES 13
- Introduction 14
- Section I 15
- Basic ePDU 15
- Accessories 17
- Operation Features 17
- Circuit breaker 18
- Table 1. Circuit Breakers 18
- Section II 19
- Monitored ePDU 19
- Ethernet Port (RJ-45) 21
- Reset Hole 21
- Circuit Breakers 21
- Display Panel 21
- Ethernet (RJ-45) 22
- Display Panel 22
- Specifications 22
- Description 23
- Hardware Setup 23
- Instructions 23
- Monitored ePDU Operation 24
- C A U T I O N 25
- Three-Phase Load Balancing 26
- Web Interface 27
- Readings 28
- Configuration 29
- Network Settings 30
- Current Alarm Settings 30
- SNMP Interface 31
- Monitored ePDU Web Interface 32
- Section III 33
- Switched ePDU 33
- SECTION3 37
- Switched ePDU Operation 38
- Table 4. Circuit Breakers 39
- Accessing the Web Interface 45
- Telnet Interface 47
- Setting Terminal Width 51
- Main Menu 52
- Outlet Control Menu 52
- Outlet Configuration 54
- Table 6. Outlet Configuration 55
- Outlet Groups 56
- Auto Scheduler 57
- Outlet Startup Mode 59
- Environmental Settings 59
- Temperature Sensor Setup 60
- Humidity Sensor Setup 61
- Contact Closure Switch Setup 62
- Unit Configuration Main Menu 64
- Unit Configuration Submenu 65
- SNMP Menus 68
- Table 13. SNMP Configuration 69
- User Manager 70
- Log Manager 71
- View Log/Alert Submenu 72
- Administrative Utilities 74
- Update Firmware 74
- Show Firmware Version 75
- Set System Defaults 75
- Outlet-Environmental Status 76
- Choose Strapping Device 77
- Unit Status 79
- Power Log 80
- Outlet Control 81
- Group Control 82
- Group Configuration 85
- Scheduler Configuration 86
- Environmental Configuration 87
- Contact Switch Settings 89
- Voltage and Current Settings 90
- Unit Configuration 91
- Switched ePDU's IP 92
- Switched ePDU. Once 92
- Network Configuration 93
- User Configuration 96
- Log Configuration 97
- Select Strapping Unit 99
- Strapping 103
- Advanced Boot Configuration 105
- after making this selection 107
- Contact Sensor Wiring 108
- Service and Support 112
- Chapter 13 Warranty 113
- *1642021151* 116
Produits connexes et manuels pour Unités de distribution d'électricité (PDU) Eaton PC917-2000
(92 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.503 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels